Wireless Joint

Also I dont know if it matters but during most of these tests I do not have a SIM card installed in the modem. Only when I move it over to the WE826 have I been putting the SIM in, as I only have one active sim and its my primary means of internet. SIM Card does not matter. You actually do not want...

Dang sorry I am going to be using a quectel ep06-a. I heard you might be stocking them is that soon? If my other order doesn't come through..i might need you for one. I doubt we will stock the EP06-A since it does not have band 41. We do stock the EM06-A which does. I mean we are both from the Sout...

Now try to flash with Generic and see what happens.

Jim thanks I was just planning on drilling a hole in the plastic... Is that to redneck? if it's not...What connector pigtails do I need? Love the site. Thanks for all the learning. Not redneck at all, partner. lol If using the MC7455, it requires 2 x U.FL to SMA Female bulkhead 5" pigtails. If...

Is that the secret sauce, limit to Band 12/2? The secret sauce is usually determined best by trial and error. If so, issue the following commands: Putty: atterm ATI AT!ENTERCND="A710" AT!BAND=10,"B12",0,800 AT!BAND=11,"B2",0,2 # Create Group AT!BAND=10,"tmob,12&qu...

Also - on the CBA850 - T-Mobile - I never see carrier aggregation become active - just states Inactive. I have done speed tests/youtube videos but nothing ... anything I need to do? Carrier Aggregation is determined by the tower, there is no way to force it. Again, are your antennas still mounted i...

As long as it is in low power mode, it will never connect.

You are going to have to get the modem to take a good flash, or return it and get another.

The WE1326 is not a bad unit. The only issue is that is has built in LTE antennas which makes it difficult to use external antennas.

What does the AT!GSTATUS? show while it is trying to connect.

It has been stable over a week now. I may try reverting it back to QMI mode to see if the stability persists. Currently in MBIM mode. You kind of hate to touch anything when it is working, more or less, flawlessly. Thanks for the update. There is a lot to be said of the old adage, that if it not br...

You are seeing MIMO RxM and RxD (i.e., Main and Diversity) on the primary carrier (PCC) but you are not seeing the secondary carrier for 2 x Carrier Aggregation.

I usually see this happen on updating the firmware when all the COM port drivers have not had time to load. Try unplugging the modem, and wait a few seconds and plug it back in. then, just forget about it for 10 minutes or so, then try flashing it again. Also, it never hurts to reload the Sierra sof...

Forgot about the spreadsheet - my bad … think I removed my previous commands.... Putty: atterm ATI AT!ENTERCND="A710" AT!BAND=12,"",0,0 With this it should had removed my previous commands entered correct? Also removed from AT Config Script. Did not do reboot or at!reset at this...

Thanks again for the information....my questions are in bold below.... I found some pigtails that I had, used those and the RSRP did not change - so I assume the LMR cables are good to go? If it did not change, then one can reasonably assume the cables are okay. During bandwidth testing, noticed my...

Question is what extra uses are there to having a SIM card slot on the mini pci-e adapter. The SIM Card slot will work for applications where there is a Mini PCI-E slot in a router or PC that does not have a SIM Card slot, or for applications where a second SIM Card is required, though not very con...

Try using this command and see is it helps:

Code: Select all

AT+QCFG="nwscanmode",3,1

That will force the modem to use LTE Only.

To re-enable it to auto mode:

Code: Select all

AT+QCFG="nwscanmode",0,1

Looks like to me it is network related. Are you certain your SIM Card is activated.

If so, you may need to put it back into the device it came from and let it re-activate.

Unplug your modem.

Plug it back in.

Run the Sierra Wireless software for Windows again.

Let it set for a few minutes to load all three COM ports.

Something is going on with your modem. It seems not to have restored, or deleted any configurations, and you have an Error.

Maybe your firmware update will fix it.

I would login and make sure the APN is also set in the user interface to keep it from overwriting the modem APN.

The configuration will be saved unless the M1 overwrites it.

If you are going to run it as two commands, then it takes:

Code: Select all

at!entercnd="A710"
AT!RMARESET=1

Well I seem to have sort of made progress. I ran Huawei Terminal as Admin and was able to issue the following commands. ATI (it then sent me a bunch of information on the modem) at!entercnd="A710" (it said "OK") !RMARESET=1 (i've been sitting here for 3 mins waiting on a respons...

You might also want to try updating the Generic firmware. Twice.

Then reset it to OEM. Then, if it takes, flash the Generic again, twice.

How much time did you give the modem to reset to OEM after entering the code? It takes a minute for it to work. If it does not return anything within a minute, enter the code a second time. Then, just give it a few.

Run this command to see if it took:

Code: Select all

AT+CGDCONT?

Might try using the following command:

Code: Select all

at+cgdcont=1,"ipv4v6","fast.t-mobile.com"

BrentV wrote: ↑Thu Jan 30, 2020 3:38 pm I'm so sorry for all the hand holding you have to do lol. Which com do I connect to? https://imgur.com/a/3YZzZKN

Please upload any images. That way they are around for others to reference.

You will also need to first install the Sierra Wireless software drivers for Windows.

When using the Huawei Terminal, connect to the WAN Modem port to issue AT Commands.

BrentV wrote: ↑Thu Jan 30, 2020 3:32 pm I won't be able to issue these commands from the WE826 the first AT command always times out. I now have the modem connected to my windows 10 machine is there a way to issue the commands from here, or should I skip to flashing the firmware?

You can use the Huawei Terminal.

BrentV wrote: ↑Thu Jan 30, 2020 3:25 pm Thank you for the reply, how do I reset the modem to OEM?

Run this AT Command:

Code: Select all

at!entercnd="A710";!RMARESET=1

Then, when it acknowledges the files have been restored/updated/deleted, issue the command to reboot the modem:

Code: Select all

AT!RESET

You can download GoldenOrb for the WRT32X HERE. It is a fairly new build and not listed on the last build list.

I was incorrect, B41 is available on the EP-06 But you may want to check if your using B41, Modem->Network Status I believe Or At command AT+CSQ I believe The EP06-A does not have Band 41. Only the EP06-E and then it lacks a lot of the other bands. This is the reason we stock the EM06-A which does ...

It is seeing the modem, so that is a good sign.

I would reset the modem to OEM, and then flash the MC7455 with latest Generic firmware (GN2) and then flash it a second time.

Thanks for the info - Terrain is flat - just trees. I will do some tuning with the antennas. Dumb question, one of the LMR cables was outside (previous setup) and I did not seal the cable. Do you see any issues? I heard if these get wet internally they are done for. That is correct. They will take ...

gurutedd wrote: ↑Wed Jan 29, 2020 2:37 pm current carrier name: mismatched
current config name: mismatched

Says this to when you do a IMPREF command.

I would reflash the modem with generic firmware, and then reflash a second time. This will generally get rid of the carrier mismatch error.

There is no way to lock to particular tower. What does the terrain look like between you and the tower? You will notice that your RSRP for the Primary Carrier (i.e., Band 2 at 10MHz of Bandwidth) is usable but may possibly be improved. I would watch these numbers while fine tuning the antenna rotati...

If it is a MC7455 (as opposed to an EM7455) you might try doing an reset to OEM.

Using the ATTERM run the AT Command:

Code: Select all

AT!GSTATUS?

That will give us a better look at both sides (MAIN & AUX) of your signals.

Thanks Jim for your quick response. I have been sending over lots of people to buy from the store today! More to follow shortly!!!!! We always appreciate that. Also, you can always go over to the ROOTer forum and ask them if the builds support the EM20-G. If it does not, chances are Dairyman will s...

If there is, it would most likely be available from HERE.

I would reload the Rooter twice, and each time uncheck the box to save settings. And, reprogram the settings and do not use a backup file.

If it worked on the bench and not in the enclosure, I would lean towards a power issue, or lack thereof.

Are you using a good Ethernet cable that is capable of carrying the voltage required.

The part of not being able to enter AT Commands is strange.

Reading the MiniPCIe-to-M.2 adapter description, I see "The adapter will ignore (i.e., not read) a SIM Card installed in a router’s SIM Card slot" which makes me doubt what The Wireless Haven told me about using it to get a 2nd SIM slot... You are most likely referring to the wrong Mini P...

Okay, it is probably best at this point to start anew. Your modem should be fine unless you have changed a lot of its configurations. You can always update the firmware at a later time once everything is working correctly. This is the plan I would follow: I would download a fresh copy of the V5 firm...

We have ran across iPad plans that are not compatible with LTE. For example:

iPad IMEI Examples.png

Now I just a minute ago reflashed the firmware back to the same version and set it up again. What did you flash, the router or modem and to what? I got the Router/Modem to allow the SIM to connect, however I'm actually not able to use the internet. That status is also below. Odd scenario, becase it...

Brandon86 wrote: ↑Thu Jan 23, 2020 5:04 pm Hey guys, has anybody had issues getting ATT sims to connect with the WE1326 Router?

I tried the broadband APN name like I use for the SIM card in all my other uses for it, but it won't connect with this router. I

What does it return when you run the AT Command:

Code: Select all

AT!GSTATUS?

Reporting the wrong bands and some of the stats is a known bug in the Sierra Wireless firmware.

You may find these of interest. They are taken from the EM7565 Product Technical Specifications.

You will note that CA requires a lot more power to the modem than one would suspect.

EM7565 DC Power Consumption.png

EM7565 Power Consumption 2.png

The EM7511 advertises Dual SIM Single Standby support. But the devices that accept it only have a single SIM card slot. thewirelesshaven suggested using the "Mini PCI-E to M.2 (NGFF) Key B Adapter with Top SIM Card Slot" and the "USB3.0 To Mini PCI-E Adapter Enclosure With SIM Card S...

We have really not heard of an under powered issue with the USB3 cables that come with the M.2 adapter enclosure. You may want to use a USB digital voltage meter to check the USB port voltage/amps on the WRT1900ACS. It is possible it is not providing enough juice to the adapter. One other way you c...

Did you also do a hard reboot of the device after upgrading the firmware, and then enter your APN and set the Time Zone.

Note that when you reset to default, it removes all custom configurations.

If you are not using IPV6, disable your TTL rules and try these in your Custom Rules.

#startTTL
iptables -t mangle -I POSTROUTING -o wwan0 -j TTL --ttl-set 65
iptables -t mangle -I PREROUTING -i wwan0 -j TTL --ttl-set 65
#endTTL

Then, if they leak, try changing the 65 to 117

Are you getting an IPV6 address?

No, I didn't put anything in. I did read before I purchased the MOFI that the "ISP TTL" was set to "Linux-2 65" by default and that was suppose to overcome the hotspot data rule. I'm open to try more. Thank you. MOFIa.jpg I would test 1117 and see it there is any change. When yo...

On top of everything I just got a notice that my hotpot data for this account is almost used up, Wasn't expecting that since I have Verizon Unlimited. Did not think it would recognize it as a hotspot. I checked the towers and they also have AT&T antennas on them so I may try them. I think AT&am...

Have you tried the Spreadsheet, selecting Band 2 and Band 12 from the drop down. Band 2 & 12.png Take the group of bands once created in the spreadsheet and go to MODEM > MISCELLANEOUS > AT-COMMAND TERMINAL and program the group run these commands (run on line at a time). AT!entercnd="A710&...

Hmm... This may be too simple of a fix, but do you have the interface Connection State for the modem set for Always on?

Always on.png

Your higher upload than download is a reasonable sign of tower congestion. A quick test to find out is to see if this changes at 3AM when the tower's resources are not being taxed. Do you know exactly where the towers are located in reference to your location? Generally, a bad ideal to install anten...

jrp320 wrote: ↑Sun Jan 19, 2020 11:21 am I get a #N/A shown where the bitmask should be if i remove or change a value. what am i doing wrong ?

What modem/device are you using?

This is what I would try. Go to SYSTEM > BACKUP/FLASH FIRMWARE RESTORE > RESET TO DEFAULTS. Once it came back on line, I would set the APN and the Time Zone. I would then test the WiFi as it is before making any changes. The WiFi on these units are far from optimal, and can be a little finicky--espe...

MBIM CONNECT: FAILED SUBSCRIBER REGISTRATION

This is a pretty good hint that it is network related.

Might call the carrier and have them reactive the SIM card.

I have very limited knowledge of these things and looking for some help. I just bought a we826 and installed a em7455 and upgraded the router firmware to the newest WiFiX golden orb. Looks like my internet is working off the lan ports but not the WiFi. I can connect to the WiFi but no internet conn...

I'm using a Linksys WRT1900ACS with the USB enclosure w/ a 3A stock power supply. External omni antennas about 4 miles from Sprint, nearly LOS. I'll let you know if I figure out a solution. It feels like it is a USB issue but I can't confirm that. I had narrowed the system & kernel log down but...

They do look better and are showing the secondary carriers for CA which appear to get a lot better signals than the Band 66 the modem is camped out on.

What band is your phone using?

You may also want to create a set of custom bands that does not include Band 66 and try them.

Signal strength looks fine, but "IMS reg state: No Srv" does not. Have your rebooted your router once or twice after the upgrade? Have you done the initial setup (MBIM/QMI mode, APN), including the selection of the "generic" firmware? The"IMS Svr: No Srv" is normal for...

Your signals are not all that good, but I have seen a lot worse. One think pops out, and that is your lack of the secondary carriers that would be used for Carrier Aggregation. LTE SSC1 state:NOT ASSIGNED LTE SSC2 state:NOT ASSIGNED LTE SSC3 state:NOT ASSIGNED LTE SSC4 state:NOT ASSIGNED The second ...

KennethClarke wrote: ↑Wed Oct 23, 2019 12:53 am
is this a known issue? or is it worth it to get a brand named router with open vpn built in and use it for the home.

Someone on the ROOter forum could better answer these questions.

You might also want to refer to GoldenOrb's tutorials HERE and HERE.

If I understand you correctly, you are trying to assign WAN (eth0.2) a static IP address?

Since it shows MBIM assigned to that interface, I assume it is the LTE interface? If so, do you have a static IP address on your cellular plan.

As Jim mentioned in his previous post, the network cannot see the router. The router cannot look like a phone IMEI since it is the modem that has the IMEI and not the router. It is the modem that transmits its IMEI to Verizon. The WE826GO is a WE826-T2 with GoldenOrb firmware loaded on it. Now if y...

The dilemma is that the E826GO has been flagged by VZ so the next strategy is to hack and hide. The E826GO will show the same IEE as the phone. Either this will work or the component within the E826GO will have to be replaced as that is now assumed to be on a VZ blacklist. The router does not conne...

The only other experience I had with no phone tech support was just the week before. That was a real scam that I exposed and recovered from. The lesson from that information is that there will be hard days and hard attitude seeking relief via getting into these products (personal conditions) of whi...

When I perform a at!gstatus? command, it says I"m connected to Channel 13, and has a verizon configuration on it. I've tried to flash it back to basic generic firmware, but it continues to display the incorrect information. Any thoughts or suggestions to remediate this bizarre situation? Regar...

is there a special way to update the firmware for the chip? or do i basically just go to flash firmware in r00ter? The modem firmware cannot be updated/flashed via GoldenOrb/ROOter. The usual process requires placing the modem in an USB to M.2 adapter and using a Windows or Linux PC. It may also be...

Search found 1343 matches