Wireless Joint

Looking at trouble shooting my EM20-G frequent disconnects. I have replaced my aux power cable to my USB adapter, and plugged in to a separate power supply away from my R7800 router, maybe that will help. In addition, I have located the Quectel Qflash app and firmware. But I’m having trouble with ac...

I have been using the EM06-A with Sprint for a little over a month now. It has been working great, very stable. I am using it in a WE826-T2 router with the WiFIX version of GoldenORB. I have not gotten band 41 to work but I think that has more to do with my location and antenna setup then anything ...

I am not aware of anyone who has tested the EM06 on Sprint, but it does have the bands for Sprint and I see no reason why it would not work. The EM12-G and EM20-G both work rather well with Sprint. As for your R7800/EM20 with the USB3 to M.2 adapter enclosure, you may try adding a second cable to t...

BillA wrote: ↑Fri Mar 06, 2020 10:17 pm For some reason they don't like to share firmware update files publicly, but will send you a link if you request it.
Make sure to specify your model# and operating system.

Email: support@quectel.com
OR
https://www.quectel.com/support/contact.htm

Thank you

BillA, I see here where you mentioned updating the firmware on the EM06, any chance you have info on how to update the firmware on the EM20. I have asked here an over on rooter for help with windows drivers an web site for firmware, but I never got any replies. Thanks.

I’m looking at setting up a device for using sprint service. Does the EM06 work right out of the box on sprint or does this need to be provisioned in order to work? From what I can see it looks like sprint uses bands 41, 25 and 26, which if I am reading correctly is supported on this modem. I was pl...

BillA wrote: ↑Sat Jan 04, 2020 9:15 pm Would you happen to know what's the make and model of the modem used in the Nighthawk M1?

No, sorry I don’t know that.

I’m using it full time right now. Seems to be working well. I have only seen 3 band CA at a time. I did have to power the optional power port to keep it running smoothly. Also noticed some buffering while on wifi while streaming, but no issue with it hard wired. There may be some WiFi tweaks that wo...

Re: Netgear MR1100 at!entercnd NOT "A710" I know this is an old post, and hope you figured it out, but there is no password required on the nighthawk M1. You just need to have the usb c of the M1 connected to the usb of your pc. I use putty to ssh into the ip of the M1 and port 5510. I hop...

Thanks for the help I will try that. FYI, I was trying to start it with only two antennas connected, I guessed wrong on which two, once I connect the right antenna, it booted fine. Thanks again.

Thanks for replying. Well, I did not make it all the way there. I was able to flash the Netgear R7800 with the flash you provided, thanks again. I was able to change the connection profile to “broadband” like I have used in the nighthawk m1 and the GL-X750. After reboot I go to Modem , Network Statu...

First off, thanks for providing all the information that is here, it’s made me believe I can attempt my own build. I have ordered the EM20 modem and USB3.0 To NGFF M.2 Key B Adapter Enclosure With SIM Card Slot from The Wireless Haven. My plan is to flash a Netgear R7800 with the current rooter vers...

I don’t have band 71, so I don’t know where it’s hex decimal goes but for my m1 to get 2+4+12+66 here is what I used AT!band=06,”LTE B2+B4+B12+B66”,0,80a,2 It’s probably just an issue, but I can’t add more than 9 lines, so I can’t use the line 10 like you have. Can you use AT!band=? To get the curre...

The only info commands I have used successfully are, :
AT!band? Which gives current band
AT!band=? Gives current band index
And like you mentioned AT!gstatus?

I could not get anything with AT!LTECA? Either

It won’t lock by itself unless you have edited it to do so, as far as I know. But I was trying to say that is what mine said when I was getting no signal at all. If you have taken it to where you know you have good signal, then I don’t know anything else to suggest.

I know this is an old post, and hope you figured it out, but there is no password required on the nighthawk M1. You just need to have the usb c of the M1 connected to the usb of your pc. I use putty to ssh into the ip of the M1 and port 5510. I hope that helps.

The only time I saw that message was when I had it band locked to a band with no signal. I removed the band lock and rebooted and it connected fine. I hope that is your problem as well.

Hi, I have a ZTE MF279 (ATT Home Base), that I cant use in my location, because I can't band lock it. I am currently using a Netgear M1 that I was able to band lock and get to work. I have another location that I'd like to use this MF279 if I can get it to band lock. I purchased a USB to PCI adapter...

Have you checked for interference for the channel your using? I know interference can cause it to drop our and lose connection.

saw2645 wrote: ↑Sun Dec 30, 2018 3:37 am Thanks for this info!
Can someone confirm that I have this right for using band 2 and band 4 on AT&T.
AT!BAND=03,”LTE B2+B4”,0,2,8

Thanks for any help!

I think I got it, it should be, AT!BAND=03,”LTE B2+B4”,0,A, not positive, but did take this one.

Again thanks for this information!

Thanks for this info!
Can someone confirm that I have this right for using band 2 and band 4 on AT&T.
AT!BAND=03,”LTE B2+B4”,0,2,8

Thanks for any help!

They are removable and look like a “mc” style board from the pictures I can find. I just don’t know if they would be locked or not.

Yes, that is what I was looking for. I just need help trying to identify whether I can use the modems I have to build one.
Are they a Sierra wireless card? How do I identify them?

I have a zte mf279 and a Netgear m1 that I tried before getting a mofi4500. I’m curious if there are any options for using the modems, best I can tell they are both using the lte Qualcomm x16 modem, for building a router modem that uses OpenWrt? Or if I’m something something other options i’d Be hap...