Wireless Joint

Hello all. I currently running two different routers running Goldenorb rooter. A Wg3526 and a Raspberry Pi 4 (different locations). Both using a EM 7455 modem. I picked up a WG1602 as I thought it might be an upgrade to the 3526. Dual sim sounded great as I have two separate cheap sim plans. On a no...

Having a string of bad luck lately that I hope to better understand, prevent, or fix. In the past month I have had a EM7565 and a MC7455 go completed dead. That is the modem stopped working however the hardware remained working (two different units - the em7565 external enclosure connected to a Rasp...

Supplied antennas only made things worse. Download is ridiculously slow. The netgear lb1121 (with the same sim band connection) consistently had better upload speeds (but not download). Seems my issue will need more trial and error to figure it out. There is something unique that I do not believe is...

That makes sense and consistent with what I have seen. As this is a remote setup that I use to upload security camera feeds and pictures, solid upload speeds are very important to me. Other than randomly trying different bands, is there a way to tell the modem to prioritize based on upload signal st...

Hello all I'm still working through various issues with my wg 3625/7455. (New mimo antenna LTWFIX 15dbi - tower about 4 miles- not direct line of sight - one mountain in the way) Download is acceptable given my cell phone has almost nothing. However, upload speeds crawl (.2 Mbps) See AT!GSTATUS? bel...

installed latest version of WiFix-NEXP1Go. Internet came back. No understanding of why, but so far so good.

I keep chugging. Good news: the wg3625 found the modem and I have an LTE connection. Bad news; No internet As I'm working with a complete new install of ROOter and that I have been using my AT&T family sim card in multiple devices since I went down. I don't know if the problem is with AT&T (...

UPDATE: Put adapter and MC7445 into a linux machine. Ran dmseg and the adapter and MC7445 was found. Red led turned on (previously had not). Removed usb adapter and put back in the Windows 10 machine. Windows found and loaded drivers. Was able to reflash (twice) the generic Sierra firmware. Perhaps ...

I received my USB To Mini PCI-E Adapter from The Wireless Haven.com. Followed the instruction given to install generic sierra drivers, check with the Huawei Terminal, and then proceed to flash with the generic Sierra MC7445 image. As this is the first time flashing the a modem card. I'm not sure if ...

I ordered a USB adapter. I'm hoping reflashing the generic sierra firmware might be something to try (would you agree?)
Not sure what else to try other than a different modem card to start and eliminate possibilities.

I did not have the opportunity to run AT!RESET as all fell apart after attempting to set all bands (No modem connected - no ability to run AT commands. I have since physically rebooted and power cycled multiple times, in addition to reflashing with both OpenWRT/modemanger and the ROOter. No change t...

If it helps. I wanted to reiterate that all was working until I remoted in to my raspberry Pi (connected to the local network, the wg3526 and the cellular WAN)using VNC and executed the following command through the ROOter web interface page: AT!BAND=00 Instantly lost my remote connection. Travelled...

I have posted the Putty screen from my SSH session.
The modem debug screen (in ROOter) is blank. I believe because the wg3526 does not find and/or load the modem. Similarly, AT commands from within Rooter or Putty do not work.

I have tried the suggestions and still remain without the ability of the WG3526 to recognize the modem Using Putty, I entered the commands echo 1199 9091 > /sys/bus/usb-serial/drivers/option1/new_id and, picocom -b 115200 /dev/ttyUSB0 which returns FATAL: cannot open /dev/ttyUSB0: No such file or di...

Thanks for the reply. The ls command returns “no such file or directory”
Hoping that can be fixed. Any suggestions or guide?

The dev directory only shows tty, ttyS0, ttyS01,ttyS02. No ttyusb.

Old thread but I have a similar problem (modem not present) and need some help fixing I have a wg3526 with Sierra mc7445. The router is mounted 30 feet in the air, thus not really convenient to get to Everything was working. Using an at&t sim. Started to play around with assigning and locking ba...

Sorry if this is a double post but I'm having little luck finding a path forward Trying set up the latest GoldenOrb 2020-03-01 on a ZBT WG3526 with a Sierra MC7445 Using AT&T Broadband I have a working IPV6 address that I can successfully ping from the outside. However, my goal is to make a conn...

Hello group. I recently completed a WG3526 with a Cat6 Sierra MC 7455 build to replace a Netgear LB1120 in a remote location running a security system and other stuff all running on solar and batteries. All is good with the WG build. I'm using an AT&T sim and receive both an IPv4 and IPv6 addres...

Hello. Great site. Tons of good information. Hoping for some help on a few issues My current rural setup consist of a Netgear LB1120 poe, mounted on a 30 foot tower with dual yagi type antennas (phased). I carry the digital signal with cat 5 back to a Asus router running wdrt. As my first attempt wi...