Wireless Joint

So After the Reset to factory, it started working again at the house on house power. I let it run all week. I did upgrade the inverter as well on the solar systems. from a 150 watt modified sine wave to a 300 watt Pure sine wave. so far it's been working for 2 days without the issue. So I think it w...

ATT- so i did a factory reset, and so far its still working. since some of the later firmware updates on the 826 i haven't had any wifi issues. I have many of these. Also have a neighbor that i support as well. So unfortunately I didn't get a cable plugged into it before I reset it. The other variab...

So maybe someone can explain this so connected via wifi I can get to the router just fine, the router can do the speed test and looks like its connecting. Last Test Date and Time : 2021-03-14 23:47:05 Starting speedtest for 10 seconds per transfer session. Test Host : netperf-west.bufferbloat.net (I...

Thanks but no joy, tried that. its really strange no mater what domain i put in the tests it connects. its just not letting wifi through. I will have to walk up there and see if it does the same for hard wired. I did go through and disable firewalls in the router etc.. with no change. even restartin...

Well from the router it is connected , I was able to reach the test sites under diagnostics. Every VPN I have tried just brings my connections to a crawl. I tried really hard one weekend to set the VPN up from the router with no luck. I didn't want to run VPN on every device i own. I really feel its...

So I just had a thought, so the router seems to ping the DNS just fine because the connection monitoring is staying up. Could this be a firmware issue between Wifi and the router?

I think I have asked this before but cant find the Thread. I have an issue with a EM12 it connects up fine with very strong signal. 100% actually. it will work for about 15 or 20 mins , stays connected but then just will not connect to the internet. Usually takes a power off and on to get it to come...

So I think i got it, first run AT+QENG="neighbourcell" +QENG: "neighbourcell intra","LTE",800,412,-16,-93,-56,0,-,-,-,-,- +QENG: "neighbourcell intra","LTE",800,254,-17,-95,-68,0,-,-,-,-,- +QENG: "neighbourcell intra","LTE",800,25...

So I think i got it, first run AT+QENG="neighbourcell" +QENG: "neighbourcell intra","LTE",800,412,-16,-93,-56,0,-,-,-,-,- +QENG: "neighbourcell intra","LTE",800,254,-17,-95,-68,0,-,-,-,-,- +QENG: "neighbourcell intra","LTE",800,25...

So I have two modems an EM12 and an EM20 both on WE826GO routers. Just recently they both can no longer connect to anything 4g. Once I set the Cellular mode to Auto then I can connect to a cell. It doesn't say what mode it is AT+QNWINFO +QNWINFO: "HSPA+","310410","WCDMA 850&...

ok i found the settings , we'll see how it goes.. Thanks!

actually i see it on both wired and wireless connections.
Im not quite understanding where to set a DNS on the router for wifi.
I have tried setting them to 8.8.8.8 on my pc and made no difference.
i will read the thread further but not sure it fits my router.

So I'm having a strange issue were my modem is connected to a strong signal but all devices can only get to Google sites. When this happens on some devices they talk about disabling ipv6 I thought it was ipv6 where they have you disable it on your device to fix the issue, this is happening on Macs ,...

Fyi both of those error out as well, starting to regret this modem purchase. It was working fine for about a month, we pretty impressed , then it just stopped connecting. now without many commands to see whats going on im at a loss. its just stuck on connecting, it sees the sim code but never connec...

so now you tell me after i spend $$$ on the EM20

i'm running on the M and M1 and it seems ok.
sometimes augmenting still on three antenna.
and FYI

Code: Select all

AT+QRSRP
ERROR

just a follow up on my situation. I purchased the EM20 and it really works great, however after a month or so , it started switching to the lower speed cell id again. I've look through the rest of the posts and was able to run the AT+QENG="servingcell" +QENG: "servingcell","...

On the EM20 there are 4 Connections M M1 M2 and D/G if only running two antenna's which should I use? Is there any benefit of running 3 ? or does it have to be 2 or 4? Is there a command to see the signal strength of each antenna? My old Sierra modem had a nice status comannd that showed that info. ...

sorry i guess this is under routers and should be under modems

On the EM20 there are 4 Connections M M1 M2 and D/G if only running two antenna's which should I use? Is there any benefit of running 3 ? or does it have to be 2 or 4? Is there a command to see the signal strength of each antenna? My old Sierra modem had a nice status comannd that showed that info. ...

Thank you Sir!!! total joy and 30 meg downloads with just stock antennas!!!

JimHelms wrote: ↑Mon Jun 22, 2020 6:38 am Use the FIRMWARE recovery method and upload the lastest WiFiX firmware which works with all versions of the EM20-G Firmware.

So I rolled back the Firmware , Im running GoldenOrb_2019-03-10 i added the startup command and I get further, now at least it connects to the modem and has the modem type listed but I keep getting these errors now Mon Jun 22 03:35:37 2020 : /dev/ttyUSB2 AT$QCPDPP=1,0 ERROR Mon Jun 22 03:35:40 2020 ...

so I'm having this same issue, just downloaded the latest Golden Orb for my ZBT-WE826 (16M) with EM20-G it sees under the device information, but I can not make any AT commands to it. I added to the startup what you have here. I also went to the other thread and made the custom port settings as sugg...

found the adapter and ordered the EM12 thanks!!

ok so these are not mini pci. so, what router do they fit in?

Your least expensive modem option with specific cell-ID/channel locking capability would be a Quectel EP/EM06-A (CAT-6), followed by the EM12 (CAT-12), EM20 (CAT-20), via the AT+QNWINFO and AT+QENG commands. Also a highly directional Yagi antenna should prevent the modem to lock onto the slower cha...

the yagi's dont seem to find the sweet spot. both cells are the same power. I just think they are switching it on me

As Didneywhorl has mentioned the Quectel EM20 can (though I haven't tried it) and some other high end models by SIMCOM. Keep in mind these are pretty expensive (in the $200-300 range). What's likely happening, is that you are between two towers with both broadcasting on band #2, and your modem is p...

Didneywhorl if you have any info on the Sierras that would be great, thats what I'm looking for.
thanks

when it switches again I'll post those results
fyi i also have tried another sim card and get the same issue.

speed test on this setting is 20 meg down 30 meg up

from the gui

MCC MNC :
310 410

RNC/eNB ID :
A1740 (661312)

LAC/TAC :
8B1E (35614)

Cell ID :
0A (10)

LTE Band :
B2 (Bandwidth 20 MHz)

Channel :
800

Maximum Qos :
-

Good Cell ID at!gstatus? !GSTATUS: Current Time: 849 Temperature: 41 Reset Counter: 1 Mode: ONLINE System mode: LTE PS state: Attached LTE band: B2 LTE bw: 20 MHz LTE Rx chan: 800 LTE Tx chan: 18800 LTE CA state: NOT ASSIGNED EMM state: Registered Normal Service RRC state: RRC Connected IMS reg stat...

ya so locking to just the band doesn't work. the band 2 works the best when it stays on cell id 10(0A) i can get the full cell id using status but in the gui that's what is says. It will stay on band 2 but switch to a different cell ID 9 still on band 2. I have tried all the aggregation combos avail...

Im sorry if this has been asked, ive done lots of research and just cant find the answer. I am currently using a MC7455 in a ZBT-WEB826 Router using Golden Orb firmware. I have found how to set the Band to the one I want and that has been working fine for over a year now. all of a sudden I keep losi...

Wireless Joint

Search found 34 matches

Re: EM12 losing what seems like DNS and internet

Re: EM12 losing what seems like DNS and internet

Re: EM12 losing what seems like DNS and internet

Re: EM12 losing what seems like DNS and internet

Re: EM12 losing what seems like DNS and internet

Re: EM12 losing what seems like DNS and internet

EM12 losing what seems like DNS and internet

How to lock an EM20 to a certain Cell.

Re: MC7455 Lock on Cell Id?

Lost Towers?

Re: We826 only allows connections to Google

Re: We826 only allows connections to Google

We826 only allows connections to Google

Re: EM20 Antenna Connection and commands?

Re: EM20 Antenna Connection and commands?

Re: MC7455 Lock on Cell Id?

EM20 Antenna Connection and commands?

Re: EM20 Questions on Antenna connections.

EM20 Questions on Antenna connections.

Re: WiFix WE826-GO and Quectel EM20-G - Modem Timeout Error

Re: WiFix WE826-GO and Quectel EM20-G - Modem Timeout Error

Re: WiFix WE826-GO and Quectel EM20-G - Modem Timeout Error

Re: MC7455 Lock on Cell Id?

Re: MC7455 Lock on Cell Id?

Re: MC7455 Lock on Cell Id?

Re: MC7455 Lock on Cell Id?

Re: MC7455 Lock on Cell Id?

Re: MC7455 Lock on Cell Id?

Re: MC7455 Lock on Cell Id?

Re: MC7455 Lock on Cell Id?

Re: MC7455 Lock on Cell Id?

Re: MC7455 Lock on Cell Id?

Re: MC7455 Lock on Cell Id?

MC7455 Lock on Cell Id?