Wireless Joint

Don't worry about the firmware in the video, just do a manual update to the latest version that's available on the Netgear support site. It's likely that you will loose all settings including the lock code after an upgrade, but you may be able to save it all to a configuration file prior to flashin...

Question, if I manually update I lose the unlock code?

I will try a manual update. The one from the youtube videos are a firmware lower than mine. I'm on 12.05.05.00

OK, 1. hard factory reset - done 2. set up APN web interface - done (adding the APN as "att" "att" then change to fast......) 3. reboot telnet AT!GSTATUS? AT!GSTATUS? !GSTATUS: Current Time: 159 Mode: ONLINE System mode: WCDMA PS state: Attached Tx Power (dBm): -24.0 GMM (PS) sta...

Jim,

I'm 100% sure is working. It is the one that I use in my daily Iphone.

/Break/


I also have a ATT SIM that if I insert it it works without problem.

BillA,

Tried your suggestion.


AT+CGDCONT?
AT+CGDCONT?
+CGDCONT: 1,"IP","fast.t-mobile.com","0.0.0.0",0,0,0,0

OK
--------------------------------

Nothing. Changes

AT!GSTATUS? AT!GSTATUS? !GSTATUS: Current Time: 518 Mode: ONLINE System mode: WCDMA PS state: Attached Tx Power (dBm): -19.0 GMM (PS) state:REGISTERED NORMAL SERVICE MM (CS) state: IDLE NORMAL SERVICE RxM RSSI C0: --- RxD RSSI C0: --- RxM RSSI C1: --- RxD RSSI C1: --- -------------------------------...

I verified the changes and are in place, APN in the web interface is fine, rebooted the nighthawk twice and still the same. At this point can I call it a faulty unit?

Run this command to see if it took: AT+CGDCONT? --------------------------------------------------------------------- AT+CGDCONT? AT+CGDCONT? +CGDCONT: 1,"IPV4V6","fast.t-mobile.com","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0 OK now it looks like it took it. Can I resta...

That's a great idea for testing purposes, but likely the router's firmware will overwrite it upon a reboot. The letters may be case sensitive in the router's menu, create the apn name as "att", the actual apn as "att", then change the actual apn to "fast.t-mobile.com" ...

at+cgdcont=1,"ipv4v6","fast.t-mobile.com" at+cgdcont=1,"ipv4v6","fast.t-mobile.com" OK AT+CGDCONT=? AT+CGDCONT=? +CGDCONT: (1-34),"IP",,,(0-3),(0-4),(0-1),(0-1) +CGDCONT: (1-34),"PPP",,,(0-3),(0-4),(0-1),(0-1) +CGDCONT: (1-34),"IPV6&qu...

"promptForApnSelection":false, "end": "" <<<<< extracted from the JSON file "restrictedApns": "nxtgenphone;ims;pta;phone;wap.cingular", "restrictedApnsEnabled": "true", -------------------------------------------------------------...

Everything seems to be ok I followed the instruction from the video and the apn is not changing if I refresh the page, there is a command line to change it directly in telnet console? I still having the sames results after watching the video.

Carriers can use various ways (TTL, UA, packet filtering) to block your data usage on non-phone devices. If you put the Tmobile sim back into a phone can you still browse the web? Make sure WiFi is off on your phone, just to check if you haven't run out of your mobile monthly data. The first test I...

I'm having a similar issue, and can't seem to figure out why, or find any info to lead me to fix it. Nighthawk M1 Unlocked, using a T-Mobile SIM. Shows Mobile Broadband Disconnected. It was working fine for a week with this setup, then over night it showed the error. I have a signal, and I can conn...